Will be the same as it was before in Raw Therapee. After generating the 3DLUT, Displa圜AL will have spat out some extra files in the output folder like a PNG file, an ICC profile and a log file. For Resolve, set the output format to 'IRIDAS (.cube)'. IF the monitor gamut was the same as sRGB, what you see in the sRGB JPG 'Apply calibration (vcgt)' should be greyed out, because your display profile does not contain any calibration data. If you export the file to sRGB, the file will have the gamut of sRGB. So if I view a photo, the photo will be displayed on my monitor to the widest color gamut the monitor can display and to my calibration settings, correct? If I then export the file as JPEG and set the colorspace to sRGB, how will that image look compared to what I see on the monitor? Will it narrow down the colorspace to sRGB in an approximation of what I see on the monitor? If I open a program, say Raw Therapee I'll have to first specify using the included calibrated profile. One last question (but it's more on colorspace than anything else). Serves you right, you flash get.I'll have to figure out why Displa圜al doesn't allow me to create a 3DLut but that's a separate issue. Got a wide gamut display? This is all probably going to be a massive pain in the arris.Though don't bother putting the location of the ICM file in gfx.color_management.display_profile 'cos if you leave it blank it'll automatically use whatever profile you've got set in your display settings. While you're in there, set gfx.color_management.enablev4 in order to take advantage of additional information in Displa圜AL's ICM profiles.Firefox needs you to go into about:config and set gfx.color_management.mode to 1, otherwise it'll only apply your colour correction profile to tagged images which will leave you spending half an hour trying to work out why the heck the pictures look different in the browser than in your image editor like an idiot YES I'M TALKING ABOUT MYSELF.Also, use Displa圜AL's handy-dandy interactive adjustment screen to match the brightnesses between your displays for best results (paying attention to the numerical figure, not the "hit the bar in the middle" arrows.) If your colorimeter has a way to measure ambient lighting, use it.Is your job not video production? Leave it alone, only madness awaits you there. Is your job video production? Congratulations, you're going to need to piss-arse about with the 3D LUTs.I can't tell if it is just the content I am viewing on it or perhaps I need a 10-bit card, or perhaps its a hardware defect A friend of mine recommended renting an x-rite idisplay pro colorimeter with the internal LG software. Don't set the curve to "As Measured" unless you want the colour correction to only apply to images in colour-managed applications you need a 1D LUT to correct non-managed stuff, like the desktop environment, and that only gets generated if you pick a curve. The in-factory calibration seems to have a lot of magenta saturation. Don't try to get smart, it's the default for a reason. Does your monitor not have a special sRGB mode that actually works? Then set the gamma curve in Displa圜AL to 2.2.Does your monitor have a special sRGB mode that actually works, unlike mine which is massively too warm? Then set the gamma curve in Displa圜AL to sRGB.Don't buy old colorimeters, they don't work.Things I has learnded throughout this process: Pretty good match to the gamma curve, though it loses it at 85-90 percent:Īnd the RGB gray balance is fine down to about 15 percent, after which it goes all skwiffy - thanks, I'm guessing, to the TN panel.Ĭonsidering each calibration takes about 20 minutes (which is a lot faster than a Spyder - apparently they take about an hour to do the same thing!) I should probably leave it there. It has, however, brought the maximum delta-E even further down:Īnd pushed those colours at the bottom of the gamut chart a bit closer to their targets (though they're still not quite there yet, and probably never will be on this monitor.) Playing some more (YES I HAVE DEADLINES TO HIT SHUT UP SHUT UP SHUT UUUUUUUUUUP!)įound an option to compensate for ambient lighting and actual environmental colour temperature as measured by the colorimeter (which, it reckons, is around 6,000K rather than 6,500K - guess my 'daylight' bulbs aren't quite up to snuff), and realised I'm probably using the gamma curve setting wrong (setting it to sRGB because that's what I want, instead of setting it to 2.2 'cos that's what the monitor reckons it's set at.)Įyeballing it, the result is that some of the colours that were washed-out on the original colour profile are a bit deeper now, though still paler than turning colour management off altogether.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |